How to Set up a Tub Yourself
Schedule And PricingAlmost everyone has their own individual way of thinking with regards to A Step-by-Step Guide to Installing a Bathtub.
Installing a bath tub isn't precisely brain surgery, but it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately tough project. If the old tub is conveniently accessible, the job can relocate rapidly; if you need to open a wall surface to remove the old tub and also position the new bath tub, the task is a lot harder. In either situation, the task is within a home handyman's abilities, although you will need an assistant to move out the old tub and also set in the new one. See to it you have certified on your own for the task and also are comfortable attempting it. As opposed to hiring a service provider to take over a halfway-completed job, it is far better to consider employing one before you start. Opportunities are you might require an expert plumber to make tube connections.
This short article will certainly assist you mount a brand-new bath tub in your restroom if you have currently acquired a new tub as well as don't require to transform the setup of your previous water supply pipelines.
Your tools and material checklist ought to make up the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is detach the water system. After doing so, switch on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing faucets can be rather troublesome as a result of the limited accessibility that is usually the case.
Use a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the faucets. Have a fabric prepared for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have been eliminated, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from turning during this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any type of old sealing compound.
Before moving on to fit the new faucets, contrast the pipeline links on the old faucets to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the various other end offers a connection to the current supply pipelines.
If you require to fit a monobloc, then you will call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin ensuring that the washing machines remain in location between the tap and also the sink. Secure the faucet in place with the manufacturer provided backnut. As soon as the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with typical tap adapters. The previous type needs to be linked to the tap finishes first, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bathtub
Making use of the two wooden boards under its feet, put the bathtub in the called for placement. The wooden boards are handy in uniformly spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto four tiny points.
The following goal is to ensure that the tub is leveled all round. This can be achieved by inspecting the spirit level and also adjusting the feet on the bathtub till the spirit level checks out degree.
To set up faucets, fit the bottom of the outermost flexible faucet connector to the ideal supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Switch on the water system and inspect all joints and also new pipework for leakages and also tighten them if required. Load the bathtub as well as also inspect the overflow electrical outlet and the normal outlet for leakages.
Finally, take care of the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub should wait until the tub has actually been used at the very least when as this will settle it right into its last position.
Getting ready for the Installment
Firstly, the supporting structure supplied with the bath ought to be fitted (if called for) according to the maker's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is important to ensure that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets system to stop pressure on the bathtub.
Fit the flexible tap ports to the bottom of the two taps using 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you make use of every one of the provided washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom ought to now be ready to be suited its final position.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to break a rigid seal, creating the water to pass through the wall between the bathroom as well as the tiling, resulting in difficulties with wetness as well as possible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and installations. They are offered in tubes and cartridges, and also are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill the bath tub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealant can crack rather early if you do not take into account this activity before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also conveniently available on the marketplace. It is advisable to fit the ceramic tiles using waterproof or waterproof adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was made aware of that article on A Step-by-Step Guide to Installing a Bathtub through a good friend on another web address. Do you know about somebody who is involved in the subject? Feel free to share it. Thanks for taking the time to read it.
Call Us Today